LEDVANCE OPTOTRONIC FIT CS G3 - OT FIT 20/220…240/500 CS
View Details
Quantity: In Stock
Selected variant:
LEDVANCE OPTOTRONIC FIT CS G3 - OT FIT 20/220…240/500 CS
Selected variant:
LEDVANCE OPTOTRONIC FIT CS G3 - OT FIT 20/220…240/500 CS
-
OT FIT 20/220…240/500 CS
- Lifetime: up to 50,000 h (temperature at max. tc)
- Cable clamp kit for independent mounting
Product family benefits
- Higher quality of light thanks to low output ripple current
- High flexibility due to four different output currents
- Small housing for flexible luminaire designs
- High efficiency
Areas of application
- Suitable for downlights, spotlights and LED panels
- Suitable for luminaires of protection classes I and II
Electrical data
- Nominal input voltage : 220…240 V
- Mains frequency : 50/60 Hz
- Input voltage AC : 198…264 V
- Total harmonic distortion : < 10 % 1)
- Power factor λ : 0.98
- Efficiency in full-load : 88 % 2)
- Device power loss : 3.0 W 3)
- Protective conductor current : <0.7 mA
- Inrush current : ≤ 4 A 4)
- Max. ECG no. on circuit breaker 10 A (B) : 38
- Max. ECG no. on circuit breaker 10 A (C) : 57
- Max. ECG no. on circuit breaker 16 A (B) : 60
- Max. ECG no. on circuit breaker 16 A (C) : 91
- Max. ECG no. on circuit breaker 25 A (B) : 94
- Surge capability (L/N-Ground) : 2 kV
- Surge capability (L-N) : 1 kV
- Nominal output voltage : 23…42 V
- U-OUT (working voltage) : 60 V
- Nominal output current : 250 / 350 / 450 / 500 mA
- Output current tolerance : ±6.5 %
- Default output current : 500 mA
- Output ripple current (100 Hz) : < 5 %
- Output PSTLM : ≤1
- Output SVM : ≤0.4
- Nominal output power : 5.8…21 W
- Maximum output power : 21 W
- Galvanic isolation : SELV
- Galvanic isolation primary/secondary : SELV
- Current set : DipSwitch
- At full load, 230 V, 50 Hz / see graphs
- at 230 V, 50 Hz
- At 230 V, Input power 24 W max.
- twidth = 50 μs typical (measured at 50 % Ipeak)
Dimensions & weight
- Mounting hole spacing, length : 88.0 mm
- Mounting hole spacing, width : 34.0 mm
- Product weight : 85.00 g
- Cable cross-section, input side : 0.5…1.5 mm²
- Cable cross-section, output side : 0.5…1.5 mm²
- Wire preparation length, input side : 7…8 mm
- Wire preparation length, output side : 7…8 mm
- Length : 97.0 mm
- Width : 43.0 mm
- Height : 29.5 mm
Colors & materials
- Casing material : Plastic
Temperatures & operating conditions
- Ambient temperature range : -20…+50 °C
- Maximum temperature at tc test point : 75 °C
- Max.housing temperature in case of fault : 110 °C
- Temperature range at storage : -20…80 °C
- Permitted rel. humidity during operation : 5…85 % 1)
- Non-condensing
Lifespan
- ECG lifetime : 50000 h 1)
- At maximum Tc = 75°C / 10% failure rate
Additional product data
- Predecessor EAN : 4052899435612
Capabilities
- Dimmable : No
- Overheating protection : Automatic reversible
- Overload protection : Automatic reversible
- Short-circuit protection : Automatic reversible
- No-load proof : Yes
- Intended for no-load operation : No
- Max. cable length to lamp/LED module : 2.0 m 1)
- Suitable for fixtures with prot. class : I / II
- Type of connection, input side : Push terminal
- Type of connection, output side : Push terminal
- Suitable for through-wiring : No
- Control interface : -
- Detection angle (Light sensor) : -
- Detection angle (PIR) : -
- Number of channels : 1
- Output wires must be routed as close as possible to each other
Programming
- Programming device : DIPswitch
Certificates & standards
- Approval marks – approval : CCC / CE / RCM / ENEC 05
- Standards : Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to / IEC 62384/Acc. to CISPR 15/Acc. to IEC 61000-3- / 2/Acc. to IEC 61000-3-3/Acc. to IEC 61547
- Type of protection : IP20
- Protection class : I,II
Specifications
Sorry, currently do not have any video uploaded.
Related Products